厦门晶鼎自动化科技有限公司特价供应，有需要前来咨询，联系人：黄先生 电话：/ Q

电缆室照明灯 CL10-W
Cable Cabinet Lamp CL10-W
CL10-W作为传统电缆室照明灯的替代方案，采用LED作为发光光源，并采取特殊的结构，实现低成本、高可靠、易用性的应用设计。
应用场合
Application
技术数据
Technical data
CL10-W
电源
power supply
AC/DC110V~230V
功耗
Power consumption
<3W
接线端子
Terminals
导线截面较大至4mm2
Conductors up to 4mm2
防护等级
Protection class
IP20
环境温度
Ambient temperature
-25 °C to +50°C
LED使用寿命
LED life span
>50,000h
耐压强度
Insulating strength
AC2000V, 50Hz, 1Min
发亮时间
Lighting continuance
1800s±15% （也可按客户要求定制）
1800s±15% (variable for demand of customer)
再次启动间隔时间
Re-start interval
不**过8秒钟
Less than 8 seconds
外壳材料
Material of enclosure
材料性能符合DIN7708标准
Insulating material according to DIN7708
连接电缆
Connecting cable
阻燃电缆2×0.5mm2，3.5米(长度可依用户需求提供)
Flame retardant cable, 3.5m(length variable for demand )
光照度
Illuminance
距离光源30cm处，≥350lx
30cm away from light source, ≥350lx
The light source control unit mounts in the safe operation re-gion, illuminance head mounts in the suitable place that the end illuminates a region in demand. Connect power, illumi-nance head take power from the light source control unit, illu-minating a region selected. After connecting power, keeping on time that gives out light is for 30 minutes, and automatical-ly goes out . If want restart, connect power again after dis-connecting power no less than 8 seconds.
Suggest: to disconnect power after every time use .
将光源控制单元安装于便于安全操作区域，发光头安装于需要照明区域的合适位置。接通电源，光源控制单元通过连接电缆点亮发光头，照亮选定区域。接通电源后，发光持续时间30分钟后自动熄灭。若要重新启动，必须在断开电源不少于8秒后再接通电源。
建议:在每次使用后断开电源。
使用方法
Use Method
The CL10-W is the substitute for the traditional cable cabinet lamp, adopt LED as light source, and adopt special structure, carry out low cost and high reliability and use easily .
安装
Installation
电缆室照明灯由光源控制单元、连接电缆和发光头组成。光源控制单元配有接线端子可直接连接电源，其中A1（+）接AC“L”或DC“+”，A2(-)接AC“N”或DC“-”，+接连接电缆红线，-接连接电缆黑线。光源控制单元安装在DIN 35mm标准导轨上，发光头可用螺栓夹紧的方式安装在电缆室需要光照的地方。
Cable cabinet lamp consists of light source control unit and connecting cable and illuminance head.The light source control unit has the wiring terminal that can connect a power supply directly, among them, the A1(+)connect the AC"L" or DC"+", the A2(-) connects the AC"N" or DC"-",the + connect the red line of connecting cable, the - connect the black line of connecting ca-ble. The control unit can mount at a standard DIN 35 mms rail.The illuminance head can fix tightly in the suitable place that the head illuminates a region in the demand with screw .